塑料线槽配线安装施工工艺标准.doc
塑料线槽配线安装施工工艺标准
1、范围
本工艺标准适用于工业和民用建筑干燥室内的电气照明明配线工程。
2、施工准备
2.1 材料要求
2.1.1 塑料线槽:由槽底、槽盖及附件组成,它是由难燃型硬聚氯乙烯工程塑料挤压成型,严禁使用非难燃型塑料加工。选用塑料线槽时,应根据设计要求选择型号、规格相应的定型产品。其敷设场所的环境温度不得低于-15℃,其氧指数不应低于27%。以上线槽内外应光滑无棱刺,不应有扭曲、翘边等变形现象。并有产品合格证。
2.1.2 绝缘导线:导线的型号、规格必须符合设计要求,线槽内敷设导线的线芯最小允许截面:铜导线为1.0mm2铝导线为2.5mm2。
2.1.3 螺旋接线钮:应根据导线截面和导线根数,选择相应型号的加强型绝缘钢壳螺旋接线钮。
2.1.4 LC安全型压线帽请见(管内穿绝缘导线安装工艺标准)有关内
Plastic trunking standard wiring Installation Process
1, range
This technology is applicable to industrial and civil construction drying chamber according to the electrical wiring works obviously.
2, construction preparation
2.1 Material requirements
2.1.1 Plastic trough: the bottom of the tank, tank cover and annexes, it is a flame-type PVC plastic extrusion, forbidden to use non-flame retardant plastics processing. Use plastic trunking should be selected according to design type, the appropriate setting product specifications. The installation site ambient temperature of not lower than -15 ℃, the oxygen index of not less than 27%. Groove above the inner and outer edges smooth without thorns, should not be distorted, such as deformation of Alice side. And a product certification.
2.1.2 Insulated wire: wire models, specifications must meet the design requirements, groove laying wire line core within the minimum allowable section: 1.0mm2 copper wire to aluminum wire is 2.5mm2.
2.1.3 Spiral Connection button: wire cross section and the conductor should be based on root number, select the appropriate type of reinforced steel spiral wire insulation button.
2.1.4 LC-safe pressure line caps, see (pipe installation process through insulated wire standard) within the
帮助中心 收藏 >>> |
本类栏目导航
总点击排行
- 天正建筑2013最新64位破解版
- 173549次
- Autocad2013 64位32位破解版附带注册机
- 154873次
- 天正建筑8.5破解版
- 146385次
- autocad2012 64位32位 破解版(附注册
- 139022次
- 天正建筑8.2破解版
- 127265次
- autocad2010免费下载(简体中文版)
- 98144次
- 免费农村房屋设计图
- 90906次
- CAD2008注册机及使用说明
- 84341次
- 11g101图集全套下载
- 78882次
- cad图集大全
- 67445次
- 天正电气8.5破解版
- 18395次
- 防雷引下线做法
- 2002次
- 国家标准图集-电气图例(CAD)
- 1320次
- 10kV及以下架空配电线路设计技术规程
- 1080次
- 山西***110kv输电线路施工组织设计(含
- 1074次
- 电气制图和识图知识
- 1020次
- 外电防护方案
- 1007次
- 铜芯电线电缆载流量标准IEC60364-5-523
- 944次
- 电梯安装施工方案
- 812次
- 线路敷设方式代号对照
- 775次