011木装饰墙身饰面技术交底记录.pdf

交底内容：
A施工准备：
2.1  材料要求：
    2.1.1  木材的树种、材质等级、规格应符合设计图纸要求及有关施工及验收规范的规定。
    2.1.2  龙骨料一般用红、白松烘干料，含水率不大于12%，材质不得有腐朽、超断面1/3的节疤、壁裂、扭曲等疵病，并预先经防腐处理。
    2.1.3  面板一般采用胶合板（切片板或旋片板），厚度不小于3mm（也可采用其它贴面板材），颜色、花纹要尽量相似。用原木材作面板时，含水率不大于12%，板材厚度不小于15mm；要求拼接的板面、板材厚度不少于20mm，且要求纹理顺直、颜色均匀、花纹近似，不得有节疤、裂缝、扭曲、变色等疵病。
    2.1.4  辅料：
    2.1.4.1  防潮卷材：油纸、油毡，也可用防潮涂料。
    2.1.4.2  胶粘剂、防腐剂：乳胶、氟化钠（纯度应在75%以上，不含游离氟化氢和石油沥青）。
    2.1.4.3  钉子：长度规格应是面板厚度的2～2.5倍；也可用射钉。
    2.2  主要机具：
    2.2.1  电动机具：小台锯、小台刨、手电钻、射枪。
    2.2.2  手持工具：木刨子（大、中、小）、槽刨、木锯、细齿、刀锯、斧子、锤子、平

Cards on the table contents:
A construction preparation:
2.1 Material Requirements:
    2.1.1 species of timber, material grades, specifications should be consistent with design drawings and the construction and acceptance requirements.
    2.1.2 keel materials in the red, white pine drying material, not more than 12% moisture content, material must not have corrupt, ultra-section 1 / 3 knots, wall split, twisted, etc. Defects in advance by the antiseptic treatment.
    2.1.3 The panel generally use plywood (cut sheet or vane plate), the thickness of not less than 3mm (also can use other plywood materials), color, pattern similar as far as possible. Panel with the original timber when not more than 12% moisture content, thickness of not less than 15mm; asked the board stitching, thickness of not less than 20mm, and asked straight texture, color uniformity, pattern similar to, not a festival scars, cracks, distortion, discoloration and other Defects.
    2.1.4 Accessory:
    2.1.4.1 moisture-proof membrane: oil paper, linoleum, moisture-proof coatings also available.
    2.1.4.2 adhesives, preservatives: latex, sodium fluoride (purity above 75% should be, without free hydrogen fluoride and petroleum bitumen).
    2.1.4.3 Nails: Length specification should be the panel thickness of 2 to 2.5 times; also available nail.
    2.2 Main equipment:
    2.2.1 Motors with: small table saws, small units planed, hand drill, shooting guns.
    2.2.2 hand tools: wooden plane (large, medium and small), groove sharpener, wood saw, fine tooth, saber saws, axes, hammers, flat