您现在的位置:主页 > 建筑工程 > 施工组织设计 > >>

油储罐施工组织设计.doc

资料评价:
★★★☆☆
更新时间:
2010-07-04
下载要求:
注册会员
文档大小:
0.02 MB
授权方式:
共享资料
上传会员:
lajks
文档类型:
.doc
所属栏目:
施工组织设计
需要金币:
1
资料语言:
简体中文
公告:免费注册 会员可立即获得金币,更多赚取金币方法请查看:金币说明 下载地址
资料简介:

油储罐施工组织设计


1. 工程概况
1. 11#储运区二车间卫七路青坎地处增建2座1000米3柴油储罐,该储罐主体结构由罐底、罐体、罐顶及附件组成,罐内储存柴油,全密封结构,直径为11米,高度为12.304米,罐底板采用搭接形式,罐壁采用对接,顶板搭接成锥体型,储罐附件主要有喷淋管、消防管及盘梯等组成,每台总重量为34.4吨,柴油卧式罐3台,V-761/A/B/C,每台总重17.405吨,柴油卧式罐平台梯子,总重6.317吨,安装时需用120吨大型吊机配合。
1.2本项目建设单位:上海石油化工股份有限公司
1.3本项目设计单位:金山石油化工设计院
1.4本项目总承包单位:中石化上海金山工程公司
2、主要实物量明细表
序号 名称和型号 材料 数量 单质量 总质量 备注
1 螺栓M1670 Q235-A 16 0.13 2.08
2 垫片RF 80-1.6B35 石棉橡胶板 2 / /
3 法兰PL80(A)-1.6RF Q235-A 4 3.59 14.36
4 盖板?104,t=10 Q235-A 2 0.67 1.32
5 角钢支架(二)L63×63×6 Q235-A、F 12 1.72 20.64
6 螺母M12 Q235-A 48 0.016 0.77
7 U型螺栓89 Q235-A 12 0.29 3.48
8 角钢支架(一)L63×63×6 Q235-A、F 4 1.77 7.08
Oil Storage Tank Construction Design


1. Project Overview
1.11 # Storage Area 2 Workshop Zinkahn Wei 7 Road, Block 2, located 1,000 meters three additional diesel storage tank, the tank of the main structure of the bottom of the tank, tank, tank top and annexes, diesel storage tank, sealed and a diameter of 11 meters, height of 12.304 meters, tank bottom using overlapping forms, tank wall by docking into a pyramidal roof lap type, main spray tank accessories tube, fire tube and spiral staircase etc., The total weight of 34.4 tons each, 3 sets of diesel horizontal tank, V-761/A/B/C, each weighing 17.405 tons, diesel fuel tank platform horizontal ladder, weighing 6.317 tons, 120 tons of essential for installation with a large crane.
1.2 The project construction unit: Shanghai Petrochemical Co., Ltd.
1.3 The project design unit: Jinshan Petrochemical Design Institute
1.4 The total project contractors: Sinopec Shanghai Jinshan Engineering Company
2, the main physical quantity schedule
Serial number name and model number of single-quality materials, the total mass of Remarks
A bolt M1670 Q235-A 16 0.13 2.08
2 RF 80-1.6B35 asbestos gasket rubber sheet 2 / /
3 flange PL80 (A)-1.6RF Q235-A 4 3.59 14.36
4 cover? 104, t = 10 Q235-A 2 0.67 1.32
Angle bracket 5 (b) L63 × 63 × 6 Q235-A, F 12 1.72 20.64
6 Nut M12 Q235-A 48 0.016 0.77
7 U-type bolt 89 Q235-A 12 0.29 3.48
8 angle bracket (1) L63 × 63 × 6 Q235-A, F 4 1.77 7.08
 

帮助中心 收藏 >>>
油储罐施工组织设计下载
点击此处下载