结构施工图审查要点(6度区。非抗震区).doc
结构施工图审查要点(6度区、非抗震区)
一、审查要点:
《工程建设标准强制性条文》(房屋建筑部分)有关地基基础、结构设计、建筑耐火等级及构件耐火极限的全部条款。
二、审查内容:
1、结构计算书
1.1 荷载取值。
符合《建筑结构荷载规范》GB50009-2001的条款和行业专门的规范、标准。民用建筑未明确的常用荷载标准值如下:浴缸、坐厕的卫生间4KN/m2;有分隔的公共卫生间8KN/m2;阶梯教室、微机房3KN/m2;银行金库、配电室、水泵房10KN/m2。注意屋面建筑找坡的荷载,墙面、楼面、天棚装饰荷载的取值是否和建筑一致。阳台、楼梯、上人屋面、走道栏杆顶部水平荷载不得遗漏。高、低屋面处在低屋面应考虑施工堆料荷载。
1.2 计算机程序分析计算。
注意软件的使用范围和技术条件,所建立的计算分析模型是否符合实际,对计算结果应先判断、校核其合理有效后,方可用于设计。必须说明软件
Elements of construction drawing review (6 degrees area, non-seismic area)
First, review the main points:
"The compulsory provisions of engineering construction standards" (Housing construction part of) the foundation, structural design, architectural elements fire resistance fire rating and all the terms.
Second, review the content:
1, structural calculations
Load value 1.1.
Compliance "structures load norms" GB50009-2001 terms and industry-specific norms and standards. Useful load is not clear civil standard values are as follows: tub, water closet toilet 4KN/m2; have separated bathroom 8KN/m2; lecture room, computer room 3KN/m2; bank vaults, power distribution room, pump room 10KN / m2. Note that the load slope roof building codes, wall, floor, ceiling decoration and construction loads are the same values. Balconies, stairs, Master roof, walkway railings at the top of the horizontal load shall not miss. High and low roof construction should be considered in low-roof stacking load.
1.2 computer program analysis and calculation.
Note the use of software, the scope and technical conditions, the Jian Li's calculation model is realistic, the calculation results should be the first Panduan, check the reasonable and effective, the before Yongyu design. Must specify the software
帮助 收藏 报错 评论>> |
本类栏目导航
总点击排行
- 天正建筑2013最新64位破解版
- 160538次
- Autocad2013 64位32位破解版附带注册机
- 148311次
- 天正建筑8.5破解版
- 144047次
- autocad2012 64位32位 破解版(附注册
- 137474次
- 天正建筑8.2破解版
- 123394次
- autocad2010免费下载(简体中文版)
- 97140次
- CAD2008注册机及使用说明
- 80812次
- 免费农村房屋设计图
- 73731次
- cad图集大全
- 56766次
- 11g101图集全套下载
- 45311次
- 钢筋平法配筋计算图解
- 1007次
- 框架结构办公楼毕业设计计算书及建筑结
- 729次
- 钢结构工业厂房毕业设计(含计算书及图
- 649次
- 钢结构工程计算手册
- 624次
- 毕业设计开题报告(土木工程结构)
- 587次
- PKPM结构软件从入门到精通
- 577次
- 剪力墙与异形柱的区别
- 499次
- 土木工程结构+毕业设计开题报告
- 465次
- 风压及雪压基本值
- 460次
- pkpm吊车荷载计算讲义
- 446次