测量工程监理细则.doc
本细则仅适用于房建中一般砖混结构和框架结构测量工程以及工业厂房中土建部分的测量工程。
一般工业与民用建筑的测量内容主要包括:建筑物的定位、轴线放样、标高复核、建筑物总高测量、建筑物的垂直度测量、建筑物沉降观测。
一、测量前准备
⒈测量前应对拟采用的测量仪器(水准仪、红外线测量仪等)进行校正和定期精度认定,以减少仪器的测量误差。
⒉校核测量配套工具,如标尺刻线、丈量长度所用圈尺的精度。
⒊准备好不同测量内容所用的测量记录表。
⒋检查判明测量用的原始点是否已破坏。
⒌测量前应确定测量方案,由于测量方案关系到测量精度,因此,测量方案应由技术负责人审核确认,其次,测量人员应有职责分工。
二、工程测量
⒈建筑物的定位测量
⑴建筑物定位测量前,应由建设项目法人提供规划测量位测量并确认的建筑物角标的坐标,(包括书面通知和现场坐标移交)角标一般为三点以上,其中两点作为定位测量用,其余点作为校核用。
⑵所提供的角标施工单位应妥善保护,当角标位于建内或施工过程可能会破坏时,应在单体定位后,引至安全地方固定好。
⑶建筑物定位测量时,以所提供的两个角标进行测量定位,然后利用其余角标反向测量校核;属角标有误时,应及时通知现场专业监理工程师和项目法人代
This rule applies only to housing under construction masonry structure and framework of the general structure of measurement engineering and industrial plant projects in the civil part of the measurement.
measurement of general industrial and civil construction content includes: building, axes lofting, elevation review, building total height measurement, the vertical measurement of buildings, building settlement observation.
1, measured preparation
⒈ measure should be adopted before the measurement equipment (Level, infrared measuring instrument, etc.) and periodic calibration precision found to reduce the instrument's measurement error.
⒉ check measurements supporting tools such as ruler engraved lines, measuring the length of the ring foot with precision.
⒊ content ready to use different measurement measurement log.
⒋ check measurements ascertained whether the original point of destruction.
⒌ measurement should be determined before measurement program, as related to the measurement accuracy measurement program, therefore, measurement programs reviewed by the technical person in charge confirmed that followed, the responsibility of surveyors division.
2, Engineering Survey
⒈ Positioning Survey of the building
⑴ building position measurement before the construction project should provide a planning measure corporate level measurement and confirmed the subject of a building corner coordinates (including coordinates of a written notice and on-site transfer) angle for the three points above the general standard, in which two points as the positioning measurement, with the remaining points as check.
⑵ angle provided by standard construction units should be properly protected in the building when the angle marked in or may be destroyed during construction shall be in the single positioning, lead to a safe place securely.
⑶ building orientation measurement in order to provide standard two angle measuring position, and then the rest of SUBSCRIPT reverse measurement check; an angle marked wrong, it should promptly notify the site professional engineer and project supervision on behalf of legal persons
帮助 收藏 报错 评论>> |
本类栏目导航
总点击排行
- 天正建筑2013最新64位破解版
- 160636次
- Autocad2013 64位32位破解版附带注册机
- 148338次
- 天正建筑8.5破解版
- 144064次
- autocad2012 64位32位 破解版(附注册
- 137474次
- 天正建筑8.2破解版
- 123404次
- autocad2010免费下载(简体中文版)
- 97153次
- CAD2008注册机及使用说明
- 80821次
- 免费农村房屋设计图
- 73777次
- cad图集大全
- 56848次
- 11g101图集全套下载
- 45449次
- 安全监理细则
- 1297次
- 安全监理实施细则(范本)
- 927次
- 船台监理细则
- 634次
- 安全监理实施细则
- 630次
- 基坑锚杆及土钉墙支护工程监理要点(细
- 571次
- 深基坑开挖工程施工质量监理细则
- 515次
- 武广客运专线武汉至花都工程JL2标后张
- 477次
- 砖混结构监理细则
- 459次
- 免费安全文明施工监理实施细则
- 437次
- 绿化工程监理实施细则
- 436次