主体模板工程技术交底.doc

一、 材料设备要求：
1． 定型组合木模板，规格为18mm厚胶合板（1220×2440），100×50方木，50mm厚木板，元钉，铁丝。
2． 钢管0.8~6m，扣件。
3． 隔离剂（成品）
二、 主要机具：
斧子、电锯、电刨、扳手、羊角锤、打眼电钻、线锤、靠尺板，方尺铁水平，撬棍等。
三、 作业条件：
1． 模板设计：根据工程结构形式和特点及施工条件，对模板进行设计，确定模板平面布置，纵横龙骨规格、数量、排列尺寸，柱箍选用的型式及间距，粱板支撑间距，模板组装形式（就位组装或预制拼装），连接节点大样。验算模板和支撑的强度、刚度和稳定性。绘制全套模板设计图（模板平面图、分块图、节点图、零件加工图）。模板数量应在模板设计时按流水段划分进行综合研究，确定模板的合理配置数量。
2． 现场拼装：
（1）、拼装场地应夯实平整，条件许可时应设拼装操作平台。
（2）、按模板设计图进行拼装，相邻两块要卡紧。
（3）、柱子模板在拼装时应留清扫口或灌浆口。               
3、模板拼装后进行编号，并涂刷隔离剂，分规格堆放。
4、放好轴线、模板边线、水平控制线标高，模板底口应做水泥砂浆找平层。检查并校正柱子位置是否正确。
5、柱子钢筋绑扎完，水电管线及埋件安装完。
四、 操作工艺：
1、装柱模板：
弹柱子位置线 → 抹找平层定位墩→ 安柱子模板→ 安柱箍→ 安拉杆或斜撑 →办自检记录。
（1）、按标高抹好水泥砂浆找平层,按位置作好定位
1, material and equipment requirements:
1. Combination of wood shaped template, specifications for the 18mm thick plywood (1220 × 2440), 100 × 50 square wood, 50mm thick wood, per nail, wire.
2. Steel 0.8 ~ 6m, fasteners.
3. Release agent (product)
Second, major equipment:
Ax, saw, planer, wrench, claw hammer, drill drill, hammer line, by foot board feet of iron levels, crowbars, etc..
Third, the operating conditions:
1. Template Design: According to the project structure and the characteristics and construction conditions, the design template to determine the template layout, vertical and horizontal keel size, number, arrangement, size, type and selected hoop column spacing, board spacing of the support beam, the template assembly form (on the Assembling or pre-assembled), a large kind of connections. Checking templates and support the strength, stiffness and stability. Draw a full set of design templates (template layout, block diagram, node graph, parts processing maps). Template number should be in the water section of the template design divided by a comprehensive study to determine the reasonable allocation of the number of templates.
2. On-site assembly:
(1), should consolidate the assembly site formation, when conditions permit, set up assembly operations platform.
(2), according to the template design for assembly, two adjacent to clamping.
(3), column template in the assembly should be left clean mouth or filling port.
3, after assembling the template code, and brushing release agent, sub-standard piling up.
4, place the axis, the template edges, the horizontal control line level, the template I should be doing the end of leveling layer of cement mortar. Check and correct the post position is correct.
5, lashing finished steel columns, water pipes and underground parts installed.
4, the operation process:
1, loaded column template:
Elastic column line of position wiping leveling layer positioning Pier → → → An An Zhuzi template column hoop → → Allah rods or braces to do self-test records.
(1), by elevation leveling layer of cement mortar smeared by location positioning