平刨车的使用安全作业交底.doc
内容摘要:
1、 手压刨必须有护手安全装置,并在操作前检查机械各部件及防护安全装置是否松动或失灵现象,并检查刨刃锋利程度及吃刀深度,经试车1-3m后,才能进行正式工作,如刨刃已钝,应及时调换。
2、 吃刀深度一般调为1-2mm。
3、 操作时左手压住木料,右手均匀推进,不要猛推猛拉,切勿将手指按于木料侧面。刨料时,先刨大面当作标准面,然后再刨小面。
4、 在刨较短、较薄的木料时,应用推板去推压木料。
5、 长度不足400mm,或薄且窄的小料不得上手压刨。
6、 在刨旧木料前,必须将料上的钉子、杂物清除干净。
7、 两人同时操作时,须待料推过刨刃150mm以外,下手方可接拖。
8、 操作人员衣袖要扎紧,严禁戴手套操作。
9、 木工机械必须实施二级漏电保护。
10、严禁操作人员在酒后进入施工现场作业。
11、每个工人进入施工现场都必须头戴安全帽。
12、班组如果因劳力不足需要再招新工人时,应事先向工地报告。
13、新工人进场后应先经过三级安全交底,并经考试合格后方可让其正式上岗。
14、新工人进场应具有四证,即:职业资质证、身份证、计划生育证和外来人口暂住证。
Abstract:
1, hand-planed pressure safety device must have a guard, and pre-operational inspection of all parts and protective mechanical safety device is loose or failure phenomena, and check the cutter blade sharp knife to eat the extent and depth of 1-3m by the post-test in order to carry out official duties, such as the cutter blade has blunt, should be transferred in good time.
2, general notes of the depth of penetration of a cutting tool 1-2mm.
3, operation, press and hold the timber left, right even to promote, do not shove yank, do not put your fingers on the wood by the side. Plane material, the first plane as a standard large area surface, and then dig a small area.
4, in the plane a short, thin wood, the application of push plate to push the wood.
5, length less than 400mm, or thin and narrow material may not fly a small plane pressure.
6, in the plane before the old wood must be material on the nails, debris cleaned.
7, the two simultaneously, they should be pushed through the cutter blade material other than 150mm, then dragging start with before.
8, the operator sleeve to be fastened operation is forbidden to wear gloves.
9, woodworking machinery to implement the secondary leakage protection.
10, prohibited operators in the drink to the construction site work.
11, each worker entering the construction site must be wearing helmets.
12 team if the need to move because of a labor shortage of new workers, the report shall be submitted to the site.
13, after the admission of new workers should go through three security correspondent, and pass the examination before they can let the official posts.
14, the new approach should have four cards of workers, namely: professional qualification certificate, identity cards, birth certificates and residence permits.
帮助 收藏 报错 评论>> |
本类栏目导航
总点击排行
- 天正建筑2013最新64位破解版
- 160786次
- Autocad2013 64位32位破解版附带注册机
- 148386次
- 天正建筑8.5破解版
- 144084次
- autocad2012 64位32位 破解版(附注册
- 137477次
- 天正建筑8.2破解版
- 123425次
- autocad2010免费下载(简体中文版)
- 97157次
- CAD2008注册机及使用说明
- 80847次
- 免费农村房屋设计图
- 73857次
- cad图集大全
- 56939次
- 11g101图集全套下载
- 45668次
- 木工安全技术交底
- 984次
- 土方回填安全技术交底
- 957次
- 环境保护与水土保持措施
- 940次
- 钻孔灌注桩安全技术交底
- 805次
- 电焊、风割焊作业安全技术交底
- 723次
- 跨铁路工程施工安全防护措施补充方案
- 622次
- 安装避雷装置图
- 580次
- 钢筋工安全技术交底
- 557次
- 施工现场的临时照明.场内交通及水电设
- 510次
- 沥青路面沥青洒布机作业-水泥混凝土路
- 491次