电杆上路灯安装技术交底-北京建工集团.doc
1 范围
本工艺标准适用于架空线路水泥电杆上的路灯安装工程。
2 施工准备
2.1 材料要求:
2.1.1 所采用的设备、器材及材料应符合国家现行技术标准的规定,并应有产品质量合格证。设备应有铭牌。
2.1.2 灯具:
2.1.2.1 配件应齐全,无机械损伤、变形、油漆剥落、灯罩破裂等现象。
2.1.2.2 灯头线截面不应小于:铜线椧?.0mm2;铝线棗2.5mm2。
2.1.3 针式绝缘子:
2.1.3.1 瓷件与铁件应结合紧密,铁件镀锌良好。
2.1.3.2 瓷釉光滑,无裂纹、缺釉、斑点、烧痕、气泡或瓷釉烧坏等缺陷。
2.1.3.3 严禁使用硫磺浇灌的绝缘子。
2.1.4 绝缘导线:
2.1.4.1 不应有扭绞、死弯、断裂及绝缘层破损等缺陷。
2.1.4.2 引下线截面不应小于:铜线棗1.5m
1 Scope
This technology is applicable to concrete poles for overhead lines on the street lamp installation.
2 construction preparation
2.1 Material Requirements:
2.1.1 the equipment used, equipment and materials should be consistent with current national technical standards and product quality certification should be. Equipment should nameplate.
2.1.2 Lighting:
2.1.2.1 Fittings shall be complete, without mechanical damage, deformation, paint peeling, broken lamp and so on.
2.1.2.2 lamp wire cross section of not less than: copper Myeong? .0 Mm2; aluminum dates 2.5mm2.
2.1.3 Pin Insulator:
2.1.3.1 ceramics should be closely combined with iron, galvanized iron good.
2.1.3.2 enamel smooth, no cracks, missing glaze spots, burn marks, defects such as bubbles or glaze burn.
2.1.3.3 Do not use sulfur water in the insulator.
2.1.4 insulated wire:
2.1.4.1 should not be twisted, dead bending, breakage and insulation damage and other defects.
2.1.4.2 deflectors section should not be less than: copper dates 1.5m
帮助 收藏 报错 评论>> |
本类栏目导航
总点击排行
- 天正建筑2013最新64位破解版
- 160514次
- Autocad2013 64位32位破解版附带注册机
- 148307次
- 天正建筑8.5破解版
- 144042次
- autocad2012 64位32位 破解版(附注册
- 137474次
- 天正建筑8.2破解版
- 123392次
- autocad2010免费下载(简体中文版)
- 97140次
- CAD2008注册机及使用说明
- 80806次
- 免费农村房屋设计图
- 73715次
- cad图集大全
- 56756次
- 11g101图集全套下载
- 45286次
- 路缘石安装技术交底记录
- 1374次
- 施工组织设计交底记录
- 1155次
- 公路施工安全技术交底
- 1047次
- 检查井施工技术交底
- 868次
- 土石方开挖施工技术交底记录
- 829次
- 排水工程雨水管施工技术交底
- 757次
- 边沟盖板安装施工技术交底记录
- 756次
- 雨水管道安装技术交底记录
- 719次
- 墩柱施工技术交底
- 668次
- 综合管沟沟槽开挖、回填施工技术交底
- 609次